CFS/HD-S High-efficiency Fine Classifier

Efficient Solution for Difficult Classifying Needs

Ogólne informacje

This high efficiency air classifier was developed for ultra-fine, sharp separation, and is often used in conjunction with grinding plants.

The optimized classifier wheel geometry produces the finest cut points and high yields that have not been possible with production scale conventional air classifiers with only one classifier wheel.

The special dispersion zone directly in close proximity to the classifier wheel uses clean gas to efficiently disperse the material to be classified.

The machine can be cleaned thoroughly, in short time when product or batches are changed, due to its highly accessible internal arrangement.

Technika

  • Finenesses up to d97 2.5 µm (based on limestone)
  • High efficiency classifier with horizontal shaft
  • Welded classifier housing with hinged door provides very good access for fast, easy cleaning and maintenance
  • Spiral housing for optimum coarse material orientation
  • Guide vane ring with adjustable vanes for efficient dispersion of the feed product prior to classification
  • Classifier wheel with exchangeable, simultaneously rotating immersion tube to achieve highest finenesses, unlimited adjustment
  • Gap between classifier wheel and fines outlet rinsed by gas for highest possible prevention of oversize material in the fine fraction
  • Classifier shaft seal rinsed by compressed gas to protect the bearings
  • Bearing of the classifier shaft is permanently grease sealed or oil lubricated for hot gas applications
  • Extremely sharp separation for improved fines extraction
  • Highest finenesses and maximum throughput achievable with just one classifier wheel
  • Even load of the classifier wheel through rotationally symmetrical design of the machine
  • Very good access for fast, easy cleaning and maintenance
  • Reproducible results
  • Optional designs available: pressure shock resistant, gas tight, wear protected
Function principle of the super-fine high efficiency fine classifier

Zastosowanie

Rudy / Minerały / Metale

 

Pigmenty / Barwniki

Ceramika / Szkło

 

Kleje / Szczeliwa

 

Celuloza / Masa włóknista

Literatura

Broszura

Broszura

The CONDUX High-efficiency Fine Classifier CFS/HD-S works very efficiently due to ist closely defined sharpness of cut and ist very specific product flow.

Broszura

For glass products, ground with dry ball mills or other mechanical Fine Mills the CFS/HD-S High Dispersion Air Classifiers can be used to remove coarse grit and provide a steeper Particle size distribution (PSD) more similar to a jet mill. Also, in some circumstances, fines removal may be desired, also to provide a steeper PSD.

Broszura

Typical toner products have a D50 in the range of 5 µm – 7 µm. NETZSCH Trockenmahltechnik GmbH entered the field of toner processing with the development of the CGS Jet Mill in the 1990’s followed by the CFS/HD-S High Dispersion Air Classifier a few years later.

Broszura

NETZSCH has developed new methods in wet and dry processing which enable a mineral processing that matches the requirements of current and future markets.

Broszura

As the global leader in particle-reduction machinery, NETZSCH offers the technology and machinery to provide true drug development solutions.

Broszura

Our long-term experience with a diversity of products in these fields, is available for your toll grinding needs.

Literatura przedmiotu

Literatura przedmiotu

The CFS-HD classifier uses a combination of the free vortex and the forced vortex models to achieve cut points down to less than 2 µm. The classifier rotor has a new design for theoretically constant radial velocity in the vane-free internal area; it is surrounded by a cage of static vanes, creating a steep spiral flow in order to give good dispersion and deagglomeration to the material to be classified.

Literatura przedmiotu

Based on the physical model of classification in vaned rotors, the fundamental difference between the exclusive use of a forced vortex flow (i.e. classification at the outer edge of the vanes) and the combined use of forced vortex/free vortex flow (i.e. classification in the interior vane free area) is derived. The classifier used for the comparison is a CFS-HDS model. Results received from this classifier equipped with a ConVor-wheel with constant radial velocity of the flow in the interior vane free area are compared with results from a classifier wheel designed for classification at the outer edge of the vanes.

Literatura przedmiotu

In the ceramic industry the mechanical treatment of raw materials, processed or finished powders is an important part of many production processes. At the same time the grinding- and classifying processes are also of primordial importance, in order to ensure a range of particle sizes which is usually exactly defined for the particular process. The grinding principle of jet milling has proved itself to be particularly effective for the grinding of ceramic and abrasive materials. They can be ground to high finenesses, with an exact upper particle size limit, in one working step.

Wasze zapytanie

Proszę kliknąć na link aby skontaktować się z naszym sprzedawcą po więcej informacji Informacja.

Być może jesteś zainteresowany:

CFS 5 HD-S and CFS 8 HD-S High-efficiency Fine Classifiers

The smallest for the finest – exact separation results for superfine powder through best possible product classification with the sharpest separation and maximum gains.

For separation limits from 2.5 to 60 µm (d97).

Machine sizes with gas volume of approximately 25 to 145 Nm³/h.

NETZSCH SmartRemoval

NETZSCH SmartRemoval is an innovative filter hose replacement system saving time and money. It combines the advantages of the conventional Top and Side Removal Systems and offsets their weak points.

Wysokowydajny separator InlineStar do produktów drobnoziarnistych

Ten nowy model separatora został zaprojektowany do połączenia na wylocie z młynem do mielenia drobnoziarnistego. Bezpośrednia integracja klasyfikatora in-line z młynem tworzy linię ciągłego mielenia i klasyfikacji o zmniejszonej liczbie wymaganych części składowych.

Dostępna separacja w granicach od 2,5 do 60 µm (d97).

Maszyny dostępne są w rozmiarach do przerabianych objętości gazu od 350 do 2 600 Nm³/h.

Młyn strumieniowo-fluidyzacyjny CGS

Połączenie młyna strumieniowego i dynamicznego separatora powietrznego: jest doskonałym sposobem na mielenie suchych produktów drobnoziarnistych. Najwyższa miałkość końcowa przy ściśle określonej maksymalnej wielkości ziarna stała się powtarzalna. Prace rozwojowe nad nowymi metodami mielenia e-Jet® i s-Jet® ciągle odsłaniają nowe, interesujące pod względem ekonomicznym i technicznym, obszary zastosowań. Stosuje się do ziarnistości od 1 do 70 µm (d97).

Maszyny dostępne są w rozmiarach do przerabianych objętości powietrza od 50 do 12 000 Nm³/h.